genie garage door starts to close then goes back up

The force setting tells the opener how much resistance the door should provide and if the opener detects more than is allowed the door will reverse. Safety sensors are the electronic eyes near the base of the door track on both sides.

Genie Garage Door Opener Troubleshooting The Genie Company

If it stops midway when going up or down it sounds like a force issue.

. Additionally a simple rebooting can help. It goes partway down reverses direction and goes back up again. Remove the wooden board from the doorway and press the wall control button to close the garage door.

First you should check the safety sensors. Check the Control Buttons. Verify if there isnt a block between them.

Check if the limits are properly set. Misaligned or blocked sensors can make your garage door fail to close. Genie Garage door problem - open after close.

The garage door openers force setting may not be set correctly. When the logic board wears out it can cause your garage door to close then open and vice versa without explanation. The logic board receives and responds signals to any remote.

Check that the door manually operates correctly. You push the button to close the garage door. This is because interference with the invisible beam helps the sensors communicate.

The symptom of this is a garage door that is in constant motion opening fully then immediately descending only to start the same cycle again. The garage door keeps going up and down. Make sure the door can stay up by itself at the 14 12 34 and fully open positions.

If your garage door keeps going back up after youve closed it the most common reason is because. Garage door starts down then STOPS and goes back up OR Safe-T-Beam System malfunction. When you try to close the door from the remote or wall unit it closes then you hear a click from around the motor unit and it goes back up.

This is almost always the result of a. Your garage door opens immediately after closing. Your garage doors logic board is the brain of your garage door opener.

This brain can wear out in time so you could need a replacement. Get Logic Board Replacement. A garage door that stops and goes back up is usually due to malfunctioning infrared sensors.

Check if the Safe-T-Beams red LED light is flashing. See How to test the balance of a garage door for more help. When the door touches the wooden board it should reverse to a fully open position within two seconds and the opener light will start flashing red as the door reverses.

Then look to see if the rollers are in working order. Your Logic Board Needs Replaced. If the wires appear to be in good shape next look at the control button mounted near your side entry door.

In the case of the first implementation the door wouldnt start to close - as long as something is obstructing the sensor the door will open completely and not attempt to close. In the case of the second implementation the door begins closing and only automatically returns to open if it meets resistance before it has completed the closing operation. This may move the chain trolley of.

If it is old or dirty the button may stick. There are four common problems with garage door sensors three of these homeowners can fix. If there is such an issue you can see one of the sensor lights blinking.

Your garage door opens when it hits the ground. There are safety sensors at the bottom of your garage door. Turn the up limit switch screw clockwise by one turn for every 3 inches that you need the garage door to raise up with a flat blade screwdriver.

They need to have a clear line-of-sight between them in order for the door to work properly. The garage door goes down then back up. Reasons Why Your Garage Door Keeps Opening After Closing.

If your garage door opens and suddenly stops it might be because of your logic board. The safety sensors are blocked. Once the door is up all the way its resting on the horizontal parts of the track and the resistance of the motor to turning because it is low geared should prevent it coming back down.

Up to 25 cash back I have a Genie model 3062 garage door opener. Once it slides down does it go back up and stop in the correct place if it doesnt maybe the gear or gear shaft on the motor is stripped. Up to 25 cash back You MUST be very careful when adjusting Force on the unitONLY turn the screw adjustment 18th of a turn at any one timeOtherwise you go to far and have to back up because the door will jam against the floor or drive will try to force door open past the stopsThat is the biggest mistake when setting force or limits.

It may be your garage door sensor. You might need to consider replacing it if your door is not working properly or you may purchase a new opener. Disconnect the GDO from the door and make sure the door can be moved easily and freely by hand.

Malfunctioning sensors can be caused by a blockage dirty eyes loose wires or just bad sensors in general. This infrared sensor passes a beam horizontally across the opening. The cause for your Genie garage door going up but not down is attributed to a problem stemming from the sensors rollers or limit switch.

Doing this can save you some amount of cash. Garage door opener keeps going back up. Make sure ONLY the safe-t-beams that came with this garage door opener are installed.

Adjust the limits as needed. If it is a NEW installation check the postion of the door arm. Press the wall control button to close the garage door.

Genie Garage Door Opener Troubleshooting The Genie Company